background image

Assemble 1/2 truss at a time, using

#10-32x7/16" bolts and square nuts,
on all connections loosely.

Attach truss lower chord to truss

upper chord.

Attach 2 center gable braces to

the upper and lower chords at the
opposite end of truss.

Attach 2 truss diagonals to upper

and lower chords.

Attach 2 mid gable braces to

upper and lower chords.

Attach 2 center gable braces to

upper and lower chords at middle of
truss.

Attach 2 outer gable braces to

upper and lower chords. Mount with
short leg of brace.

Step 1

BW14

 Parts Needed For 

Truss Assembly 12x17, 12x24 & 12x31

ONLY

 7855 Truss Lower Chord (2)

 7856 Truss Upper Chord (2)

 6382 Center Gable Brace (8)

 7739 Truss Diagonal (4)

 6381 Mid Gable Brace (4)

 6380 Outer Gable Brace (4)

 7738 Splice Plate (1)

14

6382

6382

7739

7856

Short

Mounting

Leg

#10-32 Square Nut

#10-32x7/16" Bolt

7855

6380

6381

7738

Edge Trim

Mounting Flange of Brackets

Must Face Towards Center

Of Truss Assembly

IMPORTANT:

Square Up

Half Truss

Square up 1/2 truss, adjust and

tighten.

Make other half and square.

10 

Splice both halves together with

splice plate and fasten center gable
braces together, using 3 bolts and
nuts.

11 

Cut the 4 pieces of edge trim in

half and slip over the bottom edges of
gable braces.  This trim is a must to
protect against injury from the sharp
edge.
Make 1 assembly for the 12x17
Make 2 assemblies for the 12x24
Make 3 assemblies for the 12x31

NOTE

The day before construction of the building, complete the sub-
assemblies so they will be ready.  EXAMPLE:  Truss, floor
frames, roof beams, gables, side and overhead doors.  Set the
assemblies aside, so they will not get damaged.
The remainder of the building assembly requires more than
1 work session and more than 1 person.  Do not continue
beyond this point if you do not have enough time to complete
the wall assembly and can tie down the assembly overnight.
Complete the roof and doors on the following day.

Содержание 697.68608-A












































Отзывы: