Arrow Storage Products RV101467H2 страница 30 Скачать руководство пользователя

Страница: 30 / 44

You will need for this page:

Step 11: Continued

Working with one

Gable

at a time, attach the

front

Gables

to the

Door

Track

with screws.

Do not insert screws into the two (2) holes

closest to the peak of each

Gable

. These will be used

to attach the

Track Support

later.

To secure

Gables

together, position the

Gable Brace

as shown and insert a single

bolt and nut through the second hole from the

bottom only.

Leave two (2) holes open on each side of

the Gable peak to attach Track Support.

Position

Track Support

as shown. Secure

Track Supports

Gable

using one (1) bolt

and nut. Secure to

Door Track

using two (2)

screws per side.

(QTY: 2)

Gable Brace

6636

Track Sup.

(QTY: 18)

30BF

Attach Brace with bolt

through

second hole from bottom only

Install Track Support.

Содержание RV101467H2













































Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды

Arrow Storage Products RV101467H2, Инструкция пользователя и руководство по сборке

Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды