Arrow Storage Products RV101467H2 страница 41 Скачать руководство пользователя

Страница: 41 / 44

Assemblies from Step 16:

• Right Door Assembly (1)

• Left Door Assembly (1)

(QTY: 8)

Closed Position

Half-Open Position

INSIDE BUILDING

Front Floor Frame

Door

Door Slide

Door Track

Gable

From inside the building, place the

bottom of the Door into the Front

Floor Frame track at about the half-

open position.

Rotate the Door forward until it is

vertical and align the Door Slides

with the Door.

Insert two (2) Black Screws into each

Door Slide as shown below. Repeat

steps for second door.

If Doors do not align, raise or lower one side of the Door by placing

the Door screws through a different set of holes in the Door Slide.

Door Adjustment

You will need for this page:

Step 17: Door Install

42A

Содержание RV101467H2













































Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды

Arrow Storage Products RV101467H2, Инструкция пользователя и руководство по сборке

Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды