Arrow Storage Products RV101467H2 Скачать руководство пользователя

Страница: 37 / 44

You will need for this page:

Step 13: Continued

(QTY: 72)

(QTY: 30)

37BF

6188

Right Roof

Panel

6189

Left Roof

Panel

Ridge Cap

6797

Continue to apply weather stripping.

Back

Front

6188

6189

6538

DO NOT secure end of Ridge Caps

until Peak Caps are in place.

DO NOT fully tighten Ridge Cap bolts

until you have both Ridge Cap bolts in

place. This will ease assembly. Bolts must be fully

tightened before moving on to the next page.

Attach

Front Left

and

Right Roof Panels,

one at a time,

Roof Beams

using six

(6) screws

per

Panel.

Insert bolt

and nut

in middle hole where ribs overlap.

Secure

Front Roof Panels

Gables

using seven (7) bolts

and nuts

per

Gable

Attach

Ridge Caps

with four (4) bolts and nuts. DO NOT secure end of

Ridge

Caps

until

Peak Caps

are in place.

Finish

Weather Stripping

the

Roof

and cut the tape just past the end of the

Roof

Fold end of tape under roof edge.

On both sides of the building, secure the bottom of

Roof Panels

to the

Side Wall

Angles

using screws.

Roof Panel

6538

6538

6797

Attach two(2)

Roof Panels,

one at a time,

Roof Beams

using eight (8) screws

per

Panel.

Insert bolt

and nut

in middle hole where ribs overlap.

Содержание RV101467H2













































Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды

Arrow Storage Products RV101467H2, Инструкция пользователя и руководство по сборке

Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды