Arrow Storage Products RV101467H2 страница 39 Скачать руководство пользователя

Страница: 39 / 44

(QTY: 3)

(QTY: 2)

Vert. Brace

6300

Handle

You will need for this page:

Step 15: Door Assembly

Handle Brace

3719

10477

Door

39BF

10477

3719

10497

6300

Do not fully tighten the bolts that hold on the Door

Handle until the Vertical Door Brace is in place.

Secure Door Handle and Handle Brace

to Door with two (2) bolts and nuts.

Align angled end of Brace

with upper Door Handle hole.

Place tab end of Brace

under Vertical Door Brace.

Attach Vertical Door Brace to

Door with three (3) screws.

Attach the

Door Handle

and

Door

Handle

Brace

to the

Door

with two

(2) bolts and nuts as shown. Do not

fully tighten the bolts that hold in the Door

Handle until the

Vertical

Door

Brace

is in

place.

Rotate the

Door

Handle

Brace

align it with the

Vertical

Door

Brace

as shown. Secure the

Vertical

Door

Brace

with three (3) screws. Tighten the

Door

Handle

bolts.

10477

6300

3719

Outside of Door

Install the Door Braces

on the interior (gray)

side of the Door.

Содержание RV101467H2













































Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды

Arrow Storage Products RV101467H2, Инструкция пользователя и руководство по сборке

Результаты поиска

Содержание RV101467H2

Отзывы:

Похожие инструкции для RV101467H2

Бренды по названию

Популярные бренды