manualshive.com logo in svg

Arrow Storage Products RV101467H2, Инструкция пользователя и руководство по сборке

Поделиться
Скачать
Arrow Storage Products RV101467H2 Скачать руководство пользователя страница 28

28

GABLES ARE STACKED TOGETHER 

DURING SHIPPING AND MAY BE 

MISTAKEN FOR ONE GABLE! SEPARATE 

GABLES BEFORE CONTINUING.

Large Left 

Gable

2

6109

Edge Trim MUST cover Gable edge.

Install Edge Trim to cover Gable 

Edge BEFORE doing ANY work 

with Gables. Failure to do so 

could result in injury.

(QTY: 16)

You will need for this page:

Step 11: Gables

Install 

Roof Beam Brackets

 on all 

Gables

 using 

two (2) bolts and nuts per 

Bracket

. Leg of 

Bracket

 

must face center of 

Gable

 as shown.

4

28BF

Small Left 

Gable

2

6115

Large Right 

Gable

2

6108

Small Right 

Gable

2

6114

(QTY: 8)

Bracket

4

6085

69835 

Green Edge Trim

(Plastic Piece) 

69835 

Green Edge Trim

(Plastic Piece) 

67521 

Clear Edge Trim

(Plastic Piece) 

FRONT

Apply 

Green Edge Trim

 to the top edge of the 

Large 

Left Gables

, 

Small Left Gables

, 

Large Right 

Gables

 and 

Small Right Gables

, cut to length.

1

Apply 

Clear Edge Trim

 to the edge of the 

Large Left 

Gables

 and the 

Large Right Gables

, cut to length.

2

 

Join the 

Large Gables

 to the 

Small Gables

 on the 

left and right sides using four bolts, washers and nuts 

on each side.  

3

6085

Содержание RV101467H2













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды