ARRI WCU-4 Скачать руководство пользователя страница 74

Страница: 74 / 79

Appendix

Zoom Calibration Mode

Press the

ZOOM

soft button to enter

the

Stick Setup

screen.

If the zoom control acts in the wrong

direction, move the zoom stick up-

wards and press ADJ-DIR.

If the zoom zero position is not cor-

rect (issue: the zoom motor moves

without pressing the stick), leave the

zoom stick in its center position (do

not touch it) and press ADJ-0.

Press

BACK

to return to the

SERVICE MODE

main screen. The

new calibration becomes effective af-

ter rebooting the WCU-4.

Knob Calibration Mode

Press the

KNOB

soft button to enter the

Knob Setup

screen.

Turn the knob clockwise to its end position and press

K-CW

. Then

turn the knob counter-clockwise to its end position and press

K-

CCW

Attach the WCU-4 Knob Calibration Ring K2.0000848.
Press

TEST

to check if the engravings on the Knob Calibration Ring

align with the corresponding values on the WCU-4 screen. If they

do not align, press the

K-LIN

soft button to start the knob linearizing

procedure.

NOTICE

Do not start the linearizing procedure without the ARRI

calibration ring applied. Once started, you must go through the

whole alignment procedure.
By pressing

K-LIN

all previously stored alignment points will be

cleared and cannot be restored!
Please note that previously hand-marked focus rings might have

an offset after re-calibrating the focus knob!

Содержание WCU-4
















































































Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды

ARRI WCU-4, Руководство пользователя

Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды