ARRI WCU-4 Скачать руководство пользователя страница 45

Страница: 45 / 79

Menu

Required Equipment

Wireless Compact Unit WCU-4.
Motor controller or camera, which supports LDS.
At least one lens motor. We recommend using one motor

per lens scale. If you have only one motor available but need

to add more than one lens axis, you can create the lens

scales sequentially, connecting the motor to the respective

controller connector.
SD card

Creating a Lens File
First, set up the motors on the lens and connect them to the camera

or motor controller.
Establish a wireless or wired connection between WCU-4 and the

motor controller.
Set the correct motor direction and torque.
Insert the SD card into the SD card slot of the WCU-4.
Go to MENU > LENS DATA > LENS PROGRAMMING > CREATE

LENS FILE.

Press the

CAL

soft button to calibrate the

lens motors.

Press the

SKIP

soft button if motors are al-

ready calibrated.

Содержание WCU-4
















































































Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды

ARRI WCU-4, Руководство пользователя

Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды