ARRI WCU-4 Скачать руководство пользователя страница 23

Страница: 23 / 79

Control Panel

Soft Buttons

Six soft buttons are located above and below the display. They

change their behavior depending on the screen content, indicating

the function related to each button. Buttons without a label have no

function in that screen.

Menu Navigation

To access a new menu level, press the

SELECT

soft button or

press the

USER

button.

To go one level back up, press the

BACK

soft button.

Press the

HOME

soft button to return to the

Home

screen.

Use the

UP/DOWN

soft buttons or use the zoom stick to navigate

through the menu. Keep the soft button pressed to scroll through

the list.
A parameter displayed on the right-hand of the screen can be

edited with the

CHANGE

soft button.

Press the

SET

soft button to activate a parameter list item.

Содержание WCU-4
















































































Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды

ARRI WCU-4, Руководство пользователя

Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды