ARRI WCU-4 Скачать руководство пользователя страница 60

Страница: 60 / 79

Menu

4 Press the

HWINFO

soft button. A file named “K2.72103.0-

####- wcu4.ipkg” (with #### being the WCU-4 serial

number) will be stored on the SD card in the folder /ARRI/

WCU4/Licenses.

5 Visit the ARRI license shop at http://alshop.arri.de and follow

the instructions for purchasing and downloading license

keys. This includes uploading the hardware info file.

6 Download the license key file and copy it to the SD card, to

the folder /ARRI/WCU4/Licenses.

7 Insert the SD card into the SD card slot of the WCU-4.
8 Go to

MENU > FIRMWARE > LICENSED FEATURES

9 Press the

INSTALL

soft button and select a license file from

the

INSTALL LICENSE

screen using the

UP/DOWN

soft

buttons or the zoom stick.

10 Press the

INSTALL

soft button again, and then confirm your

selection by pressing both

INSTALL

soft buttons.

11 The installed license will be indicated on the Licenses

screen.

License screens

Содержание WCU-4
















































































Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды

ARRI WCU-4, Руководство пользователя

Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды