ARRI WCU-4 Скачать руководство пользователя страница 51

Страница: 51 / 79

Menu

Use the iris slider to drive the lens zoom

scale to the next focal length mark.

Use the

and

DOWN

soft buttons or the

zoom stick to set the focal length value on

the display.

Press the

soft button or the

USER

but-

ton to set focal length point.

Do the same for the following focal length

points.

After entering all focal length points, press

the

soft button to return to the

Selec-

Axis screen.

Press the

SAVE

soft button to save

the lens file to the SD card (folder /AR-

RI/ALEXA/LDA).

Make sure to have an SD card in the

WCU-4!

Note: You can use the

FOCUS

IRIS

ZOOM

soft buttons to edit/check an ex-

isting scale or to reprogram an existing

lens scale. See "Editing a Lens File",

page 52 to learn more about editing

lens scales.

Содержание WCU-4
















































































Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды

ARRI WCU-4, Руководство пользователя

Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды