ARRI WCU-4 Скачать руководство пользователя страница 73

Страница: 73 / 79

Appendix

12.8 Service Mode

The service mode offers recalibration of focus knob, iris slider and

zoom stick. This particularly fixes a potential non-linearity of the

focus knob that can cause a misalignment with pre-marked focus

rings and hand-marked rings that are exchanged between various

WCU-4 units.
All WCU-4 units above serial number 6262 are delivered with the

extended knob calibration from the factory and usually do not need

a re-calibration.

ATTENTION!

Note: Do ONLY use the service mode if you experience issues

and need to re-calibrate the WCU-4 control devices! Make sure

that you understand the calibration procedure before using it.
To avoid unexpected interaction with an occasionally connected

motor controller, be sure the radio is disabled and no cable is

connected to the LCS socket.

To enter service mode, power up the

unit by simultaneously pressing and

holding both upper and lower cen-

ter soft buttons and the

POWER

but-

ton until the

SERVICE MODE

main

screen appears.

Содержание WCU-4
















































































Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды

ARRI WCU-4, Руководство пользователя

Результаты поиска

Содержание WCU-4

Отзывы:

Похожие инструкции для WCU-4

Бренды по названию

Популярные бренды