Arjo AtmosAir 9000A, Инструкция по эксплуатации

Страница: 22 / 316

18
Guidance and manufacturer’s declaration - electromagnetic immunity
The AtmosAir MRS LVLQWHQGHGIRUXVHLQWKHHOHFWURPDJQHWLFHQYLURQPHQWVSHFL¿HGEHORZ7KHFXVWRPHURUXVHURI
the AtmosAir MRS should assure that it is used in such an environment.
Immunity Test
IEC 60601
Test Level
Compliance Level
Electromagnetic Environment
Guidance
Electrostatic discharge (ESD)
IEC 61000-4-2
±6 kV Contact
±8 kV Air
±6 kV Contact
±8 kV Air
In accordance with
,(&ÀRRUV
are covered with synthetic
material, the relative humidity
should be at least 30%
Electrical fast
transient / burst
IEC 61000-4-4
230VAC Pump ±2 kV ±2 kV N/A
Surge
IEC 61000-4-5
1 kV line(s) to Line(s)
2 kV line(s) to Earth
1 kV line(s) to Line(s)
2 kV line(s) to Earth
N/A
Voltage dips, short interruptions and
voltage variations on power supply
input lines
IEC 61000-4-11
5% half cycle
40% for 5 cycle
70% for 25 cycle
5% for 5 seconds
5% half cycle
40% 5 cycles
70% 25 cycles
5% for 5 seconds
N/A
Power frequency
+]+]PDJQHWLF¿HOG
IEC 61000-4-8
3 A/M 3 A/M
Power frequency magnetic
¿HOGVVKRXOGEHDWOHYHOV
characteristic of a typical
location in a typical
commercial or hospital
environment.
NOTE: U, is the a.c. mains voltage prior to application of the test level.
Recommended separation distances between portable and mobile RF communications
equipment and the AtmosAir
MRS
The AtmosAir MRS is intended for use in an electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the AtmosAir MRS can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the
AtmosAir MRS as recommended below, according to the maximum output power of the communications equipment.
Rated
maximum
output power
of transmitter
W
Separation distance according to frequency of transmitter
meters
N+]WR
0+]
not applicable
0+]WR
0+]
d=[ — ] P
0+]WR*+]
d=[ — ]
P
0.01 N/A 0.12 0.23
0.1 N/A 0.37 0.74
1 N/A 1.2 2.3
10 N/A 3.7 7.4
100 N/A 12 23
For transmitters rated at a maximum output power not listed above, the recommended separate distance d in metres
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum
output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
127($W0+]DQG0+]WKHVHSDUDWLRQGLVWDQFHIRUWKHKLJKHUIUHTXHQF\UDQJHDSSOLHV
127(7KHVHJXLGHOLQHVPD\QRWDSSO\LQDOOVLWXDWLRQV(OHFWURPDJQHWLFSURSDJDWLRQLVDႇHFWHGE\DEVRUSWLRQ
DQGUHÀHFWLRQIURPVXUIDFHVREMHFWVDQGSHRSOH
3.5
E
1
7
E
1