Aritech 2X Series Скачать руководство пользователя страница 27

Страница: 27 / 36

Note:

Evacuation panels only. This feature is subject to previous configuration by

your installation or maintenance contractor and operations associated with

programmable buttons and LEDs may differ from those described here.

Enabling or disabling a previously configured sounder, fire routing, or fire

protection delay

To enable a previously configured sounder, fire routing, or fire protection delay,

press the corresponding Sounder, Fire Routing, or Fire Protection Delay button.

To disable the delay, press the button again.

Note:

Availability of this feature is subject to previous configuration and its

functionality may vary for each zone. Contact your installation or maintenance

contractor to confirm all configuration details for your site.

Viewing reports

To view system status reports for the control panel and connected devices,

select Reports from the Main menu. Report information for this user level is

shown in the table below.

Table 10: Reports available to operator users
Report

Description

Event log

Displays all alarm, fault, and condition events logged by the

control panel

Attention required

Displays all devices reporting a fault condition

Revision

Displays your control panel software revision, control panel

configuration revision, and system boards serial number data

Contact details

Displays contact information for your installation or

maintenance contractor (subject to installer configuration)

Zone status [1]

Displays the current status information for zones

Device status [1]

Displays the current status information for control panel

devices

Panel I/O status

Displays the current status information for the control panel

inputs and outputs

Output groups status [1]

Displays the control panel output groups (sounders, fire

routing, fire protection, or program) that are currently active

Rules status

Displays the control panel rules that are currently active [2]

Firenet status

Displays the current status for all control panels in the fire

network

[1] These reports are not available on repeater panels.

[2] A rule consists of one or more states (combined by Boolean operators) that are configured to

trigger specific system actions after a specific confirmation time. Rules are created by your

installation or maintenance contractor.

Note:

To check the firmware version of your control panel, select Revision report

and then select Firmware version.

Содержание 2X Series





































Результаты поиска

Содержание 2X Series

Отзывы:

Бренды по названию

Популярные бренды

Aritech 2X Series, Руководство по эксплуатации

Результаты поиска

Содержание 2X Series

Отзывы:

Бренды по названию

Популярные бренды