Aritech 2X Series Скачать руководство пользователя страница 14

Страница: 14 / 36

Icons displayed on the LCD

Icons displayed on the LCD are shown below.

Table 5: LCD icons and descriptions
Icon

Description

Day mode (network)

This icon indicates that the primary sensitivity mode

setting for control panels in the fire network is day

mode.

Day mode (control panel)

This icon indicates that the sensitivity mode for the

local control panel is day mode. Other control panels in

the fire network may have a different sensitivity mode

setting.

Night mode (network)

This icon indicates that the primary sensitivity mode

setting for control panels in the fire network is night

mode.

Night mode (control panel)

This icon indicates that the sensitivity mode for the

local control panel is night mode. Other control panels

in the fire network may have a different sensitivity

mode setting.

Fire alarms

The number beside this icon indicates the number of

zones with an active fire alarm. Alarm information for

the first and last zones to report an alarm is displayed

in the LCD message area

Faults

The number beside this icon indicates the number of

active faults. Additional information is available by

pressing F1 (Show Events).

Conditions

The number beside this icon indicates the number of

active system conditions (events). Additional

information is available by pressing F1 (Show Events).

Stand-alone

This icon indicates that the control panel is not

connected to the fire network.

Networked

This icon indicates that the control panel is connected

to the fire network.

Repeater

This icon indicates that the control panel is configured

to operate as a repeater and is connected to the fire

network.

Detector alarm [1]

This icon indicates a detector alarm.

Manual call point alarm [1]

This icon indicates a manual call point alarm.

Manual call point alarm

(sprinkler) [1]

This icon indicates a manual call point alarm

(sprinkler).

Manual call point alarm

(“hausalarm”) [1]

This icon indicates a manual call point alarm

(“hausalarm”). This is a local alarm with no fire routing

activation.

[1] These icons appear in the message display area with the notification details.

Содержание 2X Series





































Результаты поиска

Содержание 2X Series

Отзывы:

Бренды по названию

Популярные бренды

Aritech 2X Series, Руководство по эксплуатации

Результаты поиска

Содержание 2X Series

Отзывы:

Бренды по названию

Популярные бренды