Ariens 920025 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 60

Ariens 920025 Скачать руководство пользователя страница 50

EN – 46

See Figure 113.
23. Press a new front cover into gearcase.
24. Add gearcase oil. Oil level MUST be 6.1 cm – 6.7 cm

(2.4" – 2.6") from the flat surface of the gearcase
cover.

IMPORTANT:

Ariens recommends using only Ariens L3

synthetic severe duty gear lube. Using other lubricants will
not automatically void unit warranty, but the warranty will
not cover damage caused by using unauthorized
lubricants. Refer to the Operator’s Manual for your unit for
the service part numbers.
25. Reinstall seal washer (rubber side down) and oil fill

plug. Torque to 9 N•m (80 lb-in). DO NOT over-torque.

TRACK DRIVE WHEEL REPLACEMENT

Models 920028, 920318

Remove Track Drive Wheel

IMPORTANT:

Save all hardware for reinstallation.

1.

Stop engine, remove key and wait for all moving parts
to stop and for hot parts to cool.

2.

Disconnect spark plug wire from engine.

3.

Place unit in service position. See

Service Position

4.

Remove center locking flange nuts from eye bolts on
carriage assembly to release track tension. See
Figure 114.

Figure 113

WARNING:

AVOID INJURY. Before placing unit

in service position, drain fuel from tank and fuel
system. See

Draining Fuel System

Make sure unit is secure and will not tip.

Figure 114

«
...
48
49
50
51
52
...
»

Содержание 920025





























































Отзывы:

Нет отзывов