Ariens 920025 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

Ariens 920025 Скачать руководство пользователя страница 21

EN – 17

TRACTION DRIVE IDLER ARM
REPLACEMENT

Remove Traction Drive Idler Arm

IMPORTANT:

Save all hardware for reinstallation.

1.

Stop engine, remove key and wait for all moving parts
to stop and for hot parts to cool.

2.

Disconnect spark plug wire from engine.

3.

Loosen, but DO NOT remove hardware retaining belt
cover and remove belt cover.

4.

Disconnect idler spring from traction drive idler. See
Figure 29.

5.

Place unit in service position. See

Service Position

6.

Remove bottom cover. See

Bottom Cover Removal

7.

Move speed selector lever to the fastest forward
position.

8.

Remove hardware retaining traction drive idler arm
and remove idler assembly. See Figure 30.

Install Traction Drive Idler Arm

1.

Secure traction drive idler assembly to support bracket
with original hex bolt, sleeve bushing and flange nut.
See Figure 31.

2.

Reinstall bottom cover and secure with original
hardware.

3.

Return unit to operating position and reinstall traction
drive idler spring.

4.

Reinstall belt cover and secure with original hardware.

5.

Reconnect spark plug wire and fill fuel tank.

6.

Adjust traction drive clutch. Refer to operator’s manual
for instructions.

IMPORTANT:

Check all adjustments after first use.

WARNING:

AVOID INJURY. Before placing unit

in service position, drain fuel from tank and fuel
system. See

Draining Fuel System

Make sure unit is secure and will not tip.

Figure 29

Figure 30

Figure 31

«
...
19
20
21
22
23
...
»

Содержание 920025





























































Отзывы:

Нет отзывов