manualshive.com logo in svg

Ariens 920025, Руководство по обслуживанию, Страница: 43 / 60

Поделиться
Скачать
Ariens 920025 Скачать руководство пользователя страница 43

EN – 39

SCRAPER BLADE REPLACEMENT

Remove Scraper Blade

IMPORTANT: 

Save all hardware for reinstallation.

1.

Stop engine, remove key and wait for all moving parts 
to stop and for hot parts to cool.

2.

Disconnect spark plug wire from engine.

3.

Slowly tip unit back onto handlebars.

See Figure 89.
4.

Remove hardware securing scraper blade to auger 
housing and remove scraper blade.

Install Scraper Blade

IMPORTANT: 

Scraper blade is positioned above bottom 

edge of auger housing; not below.
1.

Secure scraper blade to auger housing with original 
hardware.

2.

Return unit to operating position.

3.

Reconnect spark plug wire and fill fuel tank.

4.

Adjust scraper blade and skid shoes. Refer to 
Operator’s Manual for adjustment procedures.

IMPORTANT: 

Check all adjustments after first use.

HEADLIGHT REPLACEMENT

Models 920026, 920027, 920028

Remove Bulb

IMPORTANT: 

Save all hardware for reinstallation.

1.

Stop engine, remove key and wait for all moving parts 
to stop and for hot parts to cool.

2.

Disconnect spark plug wire from engine.

3.

Remove hardware securing headlight to dash panel. 
See Figure 90.

See Figure 91.
4.

Remove headlight from dash panel.

5.

Disconnect wire harness from bulb.

WARNING: 

AVOID INJURY. Before tipping unit 

onto handlebars, drain fuel from tank and fuel 
system. See 

Draining Fuel System

 on page 7. 

Make sure unit is secure and will not fall.

Figure 89

Figure 90

Figure 91

Содержание 920025





























































Отзывы:

Нет отзывов