Ariens 920025 Скачать руководство пользователя страница 14

Страница: 14 / 60

EN – 10

IMPORTANT:

Unit must be on a flat, level surface during

steps 5 – 7.
5.

Check tire pressure and adjust if necessary. Refer to
Operator’s Manual for specification.

Torque hex bolts installed in step 4 to 22.8 N•m – 34.1
N•m (16.8 lb-ft – 25.2 lb-ft).

Loosen skid shoe hardware and adjust skid shoes.
Refer to Operator’s Manual for adjustment procedure.

See Figure 12.

Reinstall attachment drive belt onto attachment
sheave.

To assist belt installation, slowly pull recoil starter handle
while gently guiding belt onto attachment sheave.

See Figure 13.
9.

Reinstall belt finger and secure with two flat steel
washers, two locking washers and two hex bolts.

10. Check belt finger clearance:

• Engage attachment clutch lever and make sure belt

finger located opposite belt idler is less than 3.2 mm
(1/8") from belt, but not touching the belt.

• If needed, adjust clearance by loosening belt finger

hardware, repositioning belt finger, and tightening
hardware.

11. Reinstall belt cover and tighten hardware.
12. Reinstall chute rotation rod into chute rotation gear

and secure with spring clip.

13. Reinstall chute gear cover to chute pedestal and

secure with tapping screw.

14. Reinstall cable hanger onto chute rotation rod.
15. Insert chute deflector cable anchor into deflector

bracket. See Figure 4.

16. Remove sleeve bushing and hairpin from deflector

arm, reinstall cable eyelet onto deflector arm and
secure with sleeve bushing and hairpin. See Figure 4.

17. Adjust attachment clutch / brake. Refer to Operator’s

Manual for adjustment procedure.

18. Reconnect spark plug wire.

IMPORTANT:

Check all adjustments after first use.

WARNING:

AVOID INJURY. Attachment sheave

edges are sharp. Wear thick gloves to install belt
onto attachment sheave.

Figure 12

WARNING:

AVOID INJURY. Auger / impeller

must stop within 5 seconds when attachment
clutch lever is released.

Figure 13

Содержание 920025





























































Результаты поиска

Содержание 920025

Отзывы:

Ariens 920025, Руководство по обслуживанию, Страница: 14 / 60

Результаты поиска

Содержание 920025

Отзывы: