Ariens 920025 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 60

Ariens 920025 Скачать руководство пользователя страница 44

EN – 40

6.

Turn bulb one-eighth turn counterclockwise and
remove from headlight bezel. See Figure 92.

Install Bulb

IMPORTANT:

DO NOT touch new bulb with bare hands;

wear gloves. Body oil on a headlight bulb can increase bulb
temperature and reduce life of the bulb.
1.

Install bulb into headlight bezel and turn one-eighth
turn clockwise. Ensure bulb is secure.

2.

Connect wire harness to bulb.

3.

Reinstall headlight bezel into dash panel and secure
with original tapping screws.

4.

Reconnect spark plug wire.

GEARCASE REBUILD

Disassemble Gearcase

IMPORTANT:

Save all parts for reassembly, unless

otherwise specified.
1.

Remove gearcase. See

Remove Gearcase Assembly

2.

Remove any rust, if present, from auger and impeller
shafts with sandpaper. Wipe clean with oil.

3.

Remove drain plug and seal washer from gearcase.
See Figure 93.

See Figure 94.
4.

Remove hardware retaining gearcase cover and
remove cover.

5.

Remove gasket and drain gearcase.

Figure 92

Figure 93

Figure 94

«
...
42
43
44
45
46
...
»

Содержание 920025





























































Отзывы:

Нет отзывов