Ariens 916302 amp 24 sno-thro Скачать руководство пользователя страница 25

Страница: 25 / 38

GB - 25

Replace Attachment Drive Belt

1. Place new belt onto attachment pulley.

NOTE:

Hold down the attachment clutch

lever to make it easier to reconnect the
housing and frame.

2. Tip housing and frame back together

and secure with hex bolts.

3. Place belt onto drive pulley.
4. Replace belt fingers. Ensure that index

pins are properly seated.

5. Adjust clutch per

Attachment

Clutch/Brake Adjustment

on page 26.

6. Replace chute crank and secure with

spring pin.

7. Reconnect remote deflector cable to

dash control.

8. Run in the attachment belt. See

Run-in

Attachment Belt

on page 12.

9. Replace belt cover.

TRACTION DRIVE BELT

REPLACEMENT

1. Move PTO and power switches to OFF

position.

2. Disconnect and remove batteries.

3. Place the unit into the service position

on a level surface (see

Service Position

on page 19).

4. Remove the bottom cover by removing

six cap screws.

NOTE:

To gain belt clearance, remove swing

gate spacer (Figure 28) so drive plate can be
slid over until finger is out of frame and drive
plate can swing past stop hole in frame. See
Figure 29.

WARNING:

AVOID INJURY. Auger

must stop within 5 seconds when

attachment lever is released or

serious injury or unit damage may

result.

Figure 26

OS2625

1. Pinion Gear
2. Belt Cover

3. Spring Pin
4. Chute Crank

CAUTION:

Before tipping unit up

onto housing, both batteries must be

removed from the unit. Ensure unit is

secure and will not tip over during

maintenance.

Figure 27

OS2623

1. Traction Belt

Idler

2. Traction

Drive Belt

3. Drive Pulley
4. Belt Finger
5. Attachment

Drive Belt

6. Attachment

Pulley

7. Attachment

Idler Nut

8. Attachment

Belt Idler

Содержание 916302 amp 24 sno-thro







































Результаты поиска

Содержание 916302 amp 24 sno-thro

Отзывы:

Похожие инструкции для 916302 amp 24 sno-thro

Бренды по названию

Популярные бренды

Ariens 916302 amp 24 sno-thro, Руководство пользователя

Результаты поиска

Содержание 916302 amp 24 sno-thro

Отзывы:

Похожие инструкции для 916302 amp 24 sno-thro

Бренды по названию

Популярные бренды