Ariens 916302 amp 24 sno-thro Скачать руководство пользователя страница 26

Страница: 26 / 38

GB - 26

5. Pull idler away from traction drive belt

and remove belt from idler, drive pulley

and driven pulley.

6. Replace traction drive belt.
7. Swing drive plate toward friction disc to

slide finger into stop hole in frame.

Reinstall swing gate spacer.

NOTE:

Make sure drive plate spring remains

connected to the frame and drive plate.

8. Replace attachment drive belt (See

Replace Attachment Drive Belt

page 25).

ATTACHMENT CLUTCH/BRAKE

ADJUSTMENT

Remove Attachment Cable Slack

1. Loosen the hardware securing belt

cover to unit.

NOTE:

DO NOT completely remove the

hardware from unit.

1. Remove the belt cover.
2. Loosen jam nut (3) on cable adjustment

barrel (2), and then turn the adjustment

barrel down to shorten cable and

remove all cable slack. See Figure 30.

3. With the attachment clutch disengaged,

check that the attachment idler arm

lightly touches the frame. See Figure 31.

4. Tighten jam nut on cable adjustment

barrel.

Figure 28

OS2630

1. Swing Gate Spacer
2. Drive Plate

Figure 29

OS8068

1. Swing Gate
2. Swing Gate Finger
3. Drive Plate

WARNING:

IMPROPER

ADJUSTMENT could result in

unexpected movement of auger and

impeller causing death or serious

injury. AUGER / IMPELLER MUST

STOP within 5 seconds when

Attachment Clutch/Impeller Brake

Lever is released.

Figure 30

1. Attachment Clutch Cable
2. Cable Adjustment Barrel
3. Jam Nut

OS2645

Содержание 916302 amp 24 sno-thro







































Результаты поиска

Содержание 916302 amp 24 sno-thro

Отзывы:

Похожие инструкции для 916302 amp 24 sno-thro

Бренды по названию

Популярные бренды

Ariens 916302 amp 24 sno-thro, Руководство пользователя

Результаты поиска

Содержание 916302 amp 24 sno-thro

Отзывы:

Похожие инструкции для 916302 amp 24 sno-thro

Бренды по названию

Популярные бренды