Ariens 916302 amp 24 sno-thro страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 38

background image

GB - 6

SAFETY DECALS AND

LOCATIONS

ALWAYS replace missing or damaged Safety
Decals. Refer to figure below for Safety Decal
locations.

1. WARNING!

2. DANGER!

3. DANGER!

SAFETY RULES

Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly or operating. Failure to
follow instructions could result in personal
injury and/or damage to unit.
ALWAYS disconnect batteries before
assembly, maintenance or service.
Unintentional drive motor start up can cause
death or serious injury.
Complete a walk around inspection of unit
and work area to understand:
• Work area • Your unit • All safety decals

Read Owner/Operator Manual.

Keep people away from unit while
operating. Keep children out of
work area and under watchful care
of a responsible adult.

Never direct discharge towards
persons or property that may be
injured or damaged by thrown
objects.

Stop drive motor, remove key,
read manual before making any
repairs or adjustments.

Figure 2

OS2500

1

2

3

OL1801

OL4370

OL0910

OL4010

Wear appropriate hearing
protection.

ONLY use clean-out tool to clear
blockages. NEVER use your
hands.

ROTATING PARTS! ONLY use
clean-out tool to clear blockages.
NEVER use your hands.

High

speed impeller rotates below
discharge opening. Wait for all
moving parts to stop before
removing clogs or servicing.

ROTATING PARTS.

Keep clear of auger while unit is
running.

•

Read Operator’s Manual.

•

Allow operation only by

properly trained adult,

never children.

•

Stop drive motor and

remove key prior to leaving

the operator’s position for

any reason.

•

Keep all controls, guards

and safety devices properly

serviced and functional.

•

Never direct discharge

towards persons or

property that may be

injured or damaged by

thrown objects.

OL4690

OS6610

OS2080

«
...
4
5
6
7
8
...
»

Содержание 916302 amp 24 sno-thro







































Отзывы:

Нет отзывов

Похожие инструкции для 916302 amp 24 sno-thro

Бренд: GreenWorks Страницы: 116

Бренд: MAGIC FX Страницы: 20

Бренд: Hurricane Страницы: 60

Бренд: Ryobi Страницы: 16

Бренд: WARRIOR Страницы: 33

Бренд: Stihl Страницы: 32

Бренд: WIFO Страницы: 4

MULTIAIR FC 1000

Бренд: Kongskilde Страницы: 100

Бренд: Anest Iwata Страницы: 7

Бренд: Texas Equipment Страницы: 11

Бренд: Texas Equipment Страницы: 12

Бренд: Texas Equipment Страницы: 16

Бренд: Texas Equipment Страницы: 18

Бренд: Gude Страницы: 40

Бренд: RedMax Страницы: 28

Бренд: Cramer Страницы: 6

Бренд: Kobalt Страницы: 22

Бренд: Pelsue Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды