background image

GB - 5

DELIVERY

Customer Note: 

If you have purchased this 

product without complete assembly and 
instruction by your retailer, it is your 
responsibility to:

1. Read and understand all assembly 

instructions in this manual. If you do not 

understand or have difficulty following 

the instructions, contact your nearest 

Ariens Dealer for assistance. Make sure 

all assembly has been properly 

completed.

NOTE: 

To locate your nearest Ariens Dealer, 

go to www.ariens.com on the Internet.

2. Understand all Safety Precautions 

provided in the manuals.

3. Review control functions and operation 

of the unit. Do not operate the Sno-Thro 

unless all controls function as described 

in this manual. 

4. Review recommended lubrication, 

maintenance and adjustments.

5. Review Limited Warranty Policy. 
6. Fill out a Product Registration Card and 

return the card to the Ariens Company or 

go to www.ariens.com.

SAFETY ALERTS

Look for these symbols to point 
out important safety precautions. 
They mean:

Attention!   
Personal Safety Is 
Involved!
Become Alert! 
Obey The Message!

The safety alert symbols above and signal 
words below are used on decals and in this 
manual. Read and understand all safety 
messages.

 

NOTATIONS

NOTE: 

General reference information for 

proper operation and maintenance practices.

IMPORTANT: 

Specific procedures or 

information required to prevent damage to 
unit or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working 
precautions, for the benefit of yourself and 
others. Understand and follow all safety 
messages. Be alert to unsafe conditions and 
the possibility of minor, moderate, or serious 
injury or death. Learn applicable rules and 
laws in your area. Always follow the practices 
set forth in this manual.

REQUIRED OPERATOR 

TRAINING

Original purchaser of this unit was instructed 
by the seller on safe and proper operation. If 
unit is to be used by someone other than 
original purchaser; loaned, rented or sold, 
ALWAYS provide this manual and any 
needed safety training before operation.

WARNING: 

Improper assembly or 

adjustments can cause serious 

injury.

SAFETY

WARNING: 

To avoid injury to hands 

and feet, always disengage clutches, 

stop drive motor, turn off and remove 

key from switch and wait for all 

movement to stop before unclogging 

or working on snow thrower.
Hand contact with the rotating 
impeller is the most common cause of 
injury associated with snow throwers. 
Never use your hand to clean out the 
discharge chute.
Keep hands and feet away from 
auger and impeller.

DANGER: 

IMMINENTLY 

HAZARDOUS SITUATION! If not 

avoided, WILL RESULT in death or 

serious injury.

WARNING: 

POTENTIALLY 

HAZARDOUS SITUATION! If not 

avoided, COULD RESULT in death or 

serious injury.

CAUTION: 

POTENTIALLY 

HAZARDOUS SITUATION! If not 

avoided, MAY RESULT in minor or 

moderate injury. It may also be used 

to alert against unsafe practices.

Содержание 916302 amp 24 sno-thro







































Отзывы: