Arcus DMX-CAN-23 Скачать руководство пользователя страница 70

Страница: 70 / 74

DMX-CAN Manual

page 70

rev 1.6

DEC

Get deceleration value in milliseconds. Only used if
EDEC=1

Milli-seconds

DEC=[Value]

Set deceleration value in milliseconds. Only used if
EDEC=1

Return status of digital inputs

6-bit number in decimal.

DI[1-6]

Return status of individual input

1 or 0

Return device name

DMK00-DMK99

DN=[Device ID]

Set device name.
Range:

DMC01 to DMC99

Note: Address 00 is reserved for broadcasting over RS-485

Return status of digital outputs

3-bit number

DO=[Value]

Set digital output 3 bit number. Note that DO1 and DO2 can
only be used as general purpose when StepNLoop is disabled

DO[1-3]

Return status of individual digital output

1 or 0

DO[1-3] = [Value]

Set individual digital output

DOBOOT

Get DO boot-up state

See Table 7.1

DOBOOT=[Value]

Set DO boot-up state

Returns the delta value during StepNLoop control

32-bit number

EDEC

Get unique deceleration enable

0 or 1

EDEC=[Value]

Set unique deceleration enable

EDO

Returns enable alarm/in pos mode status

1 – enabled
0 – disabled

EDO=[0 or 1]

Enables (value 1) or disable (value 0) alarm/in pos mode

Returns driver power enable status.

1 – Motor power enabled
0 – Motor power disabled

EO=[0 or 1]

Enables (value 1) or disable (value 0) motor power.

EOBOOT

Get EO boot-up state

0 or 1

EOBOOT=[Value]

Set EO boot-up state

Returns current encoder counter value

32-bit number

EX=[Value]

Sets the current encoder counter value

H+

Homes the motor in positive direction

H-

Homes the motor in negative direction

HL+

Homes the motor in positive direction (with with low speed)

HL-

Homes the motor in negative direction (with low speed)

HSPD

Returns High Speed Setting

Value in PPS

HSPD=[Value]

Sets High Speed.

Returns product ID

DriveMax-CAN

INC

Set move mode to incremental

J+

Jogs the motor in positive direction

J-

Jogs the motor in negative direction

L+

Homes the motor in the positive direction using the limit
switch.

L-

Homes the motor in the negative direction using the limit
switch.

LCA

Return the limit correction amount

32-bit number

LCA=[Value]

Set the limit correction amount

LSPD

Returns Low Speed Setting

Value in PPS

LSPD=[Value]

Sets Low Speed

LT=[0 or 1]

Enable or disable position latch feature

LTE

Returns latched encoder position

32-bit number

LTP

Returns latched pulse position

32-bit number

Содержание DMX-CAN-23











































































Результаты поиска

Содержание DMX-CAN-23

Отзывы:

Бренды по названию

Популярные бренды

Arcus DMX-CAN-23, Руководство пользователя

Результаты поиска

Содержание DMX-CAN-23

Отзывы:

Бренды по названию

Популярные бренды