Arctic Spas Arctic Fox Скачать руководство пользователя

Страница: 11 / 124

Owners Manual - Arctic Spas®

Installation Instructions

Site Preparation

Please ensure the following:

• Always put your spa on a structurally sound, level surface. A filled spa can weigh a great deal.

Make certain that the location you choose can support the weight of your filled spa.

• Locate your equipment compartment, which houses all of electrical components, in a place

where you will have easy access for periodic spa care and maintenance.

• Allow adequate access to all other doors for service.

Outdoor Ground Level Installation

No matter where you install your new spa, it’s important that you have a solid foundation for support. If

you are installing a spa with a wooden pedestal floor outdoors, we recommend you place patio stones

underneath spaced out evenly. The stones should be at least two inches thick and twelve inches square (30

cm x 30 cm). Even with stones in place, the spa will possibly settle and become uneven, and may require

re-leveling over time. If you are installing a spa with a Forever Floor® outdoors, you may set it on virtually

any surface, as long as it is firm and level.

Deck Installation

To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult

a qualified building contractor or structural engineer. To find the weight of your spa, its contents and

occupants, refer to the Spa Specification chart. This weight per square foot must not exceed the structure’s

rated capacity, or serious structural damage could result.

Your Arctic Spas® Dealer can help you with local information such as zoning regulations and building

codes.

All Weather Pool Site Prep

Your new All Weather Pool should be placed on a prepared, uniformly solid and level surface (concrete pad,

properly engineered wood deck, etc.). The AWP should not be placed directly on a lawn, bare ground, or

gravel pad due to irregularities in the surface that may cause structural failure of the cabinet and shell that

could void the warranty.

Balconies, concrete pads, and decks should

be constructed to meet all builder codes and

should be able to or exceed supporting 146

Lbs per square foot (7kPa).

Your Arctic Spa is equipped with access

doors on all four sides. It is the customer’s

responsibility to provide access and ensure

there is a minimum of 24” (600mm) all around

the spa for service person access. Consult

your sales person or service department on the

different ways to achieve this clearance.

WARNING! WARNING!

We recommend that the Arctic Spa be installed

above ground. Consult a licensed building

contractor to design or evaluate your custom

decking requirements. Please ensure access to all

doors on all 4 sides of the spa for serviceability.

Содержание Arctic Fox





























































































































Результаты поиска

Содержание Arctic Fox

Отзывы:

Похожие инструкции для Arctic Fox

Бренды по названию

Популярные бренды

Arctic Spas Arctic Fox, Руководство пользователя

Результаты поиска

Содержание Arctic Fox

Отзывы:

Похожие инструкции для Arctic Fox

Бренды по названию

Популярные бренды