manualshive.com logo in svg

Arcomed Volumed uVP7000 Premium, Руководство по обслуживанию, Страница: 44 / 53

Поделиться
Скачать
Arcomed Volumed uVP7000 Premium Скачать руководство пользователя страница 44

SH-7000-Pre-E-04/16 

43 

7

 

Calibration

 

The pump must calibrated with the final user IV set. Only one brand of IV set is allowed.  
All calibrations must be done with the pump on configuration 0. 
To start up the pump in Setup Mode, please refer to chapter 

2.

 

 

7.1

 

Pressure Sensor 

The built in pressure sensor of the Volumed® µVP7000 Chroma has to be adjusted first 
mechanically and then by means of software. The mechanical adjustment is necessary 
after replacement or if the software adjustment is not sufficient.  

 

Used tools:

 

 
- 2.5 mm Hex driver 
- 0,89 mm Hex driver 
- Infusion giving set filled with water 
- Manometer with three ways tab. A syringe filled with water must be connected to the    
  manometer.  
    

 

Procedure: 

1. 

Turn off pump and unplug open housing according to instructions for changing the 
Main PCB (6.2.1). 

2. 

Dismantle the Pump block (6.2.4) 

Содержание Volumed uVP7000 Premium






















































Отзывы:

Нет отзывов