manualshive.com logo in svg

araknis 210 Series, Руководство по эксплуатации продукта

Поделиться
Скачать
araknis 210 Series Скачать руководство пользователя страница 68

© 2020 Araknis Networks

®

68

Araknis Networks AN-210/310-SW-F/R Manual

Product Manual

Table of Contents

Port Settings

Configure 802.1x settings for each switch port.

Figure 30. 

802.1x Port Settings Menu

• 

Port –

 Switch port identifier.

• 

Mode –

 Options:

• 

Disabled –

 802.1x is disabled through the port.

• 

Auto –

 Port allows only packets used for authentication and network discovery until the client is 

authenticated, then allows uninterrupted traffic.

• 

ForceUnAuthorized –

 The port will remain unauthorized state and ignore all attempts to 

authenticate a client.

• 

ForceAuthorized –

 The port always behaves as if an authenticated client is connected.

• 

Reauthentication –

 Enable or disable reauthentication by the switch. If enabled, a client that failed to 

authenticate will not be allowed to try again until the next period based on the Period Setting.

Default: Enabled

• 

Reauthentication period –

 Set the reauthentication period.

Default: 3600 seconds

• 

Quiet Period –

 Set the quiet period.

Default: 60

• 

Supplicant Period –

 Set the Supplicant period.

Default: 30

• 

Max Retry –

 Set the Max Retry value.

Default: 2

• 

Authorized Status –

 Displays the current authorization status of the port.

• 

Guest VLAN –

 Enable or disable guest VLAN use for the port.

Default: Enabled
Default: 

Содержание 210 Series








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды