Galaxy 3 Operating Manual
17
Section 6
Internet Communications
There are three ways to communicate with the internet from the
Galaxy 3. For highspeed internet, you will need a working
router, Ethernet and/or WiFi Communications.
6.1 LeagueLeader Setup
If you intend on using the Galaxy 3 for leagues or Remote
Play, you need to add the settings to the machine.
Note: You can set up the Connections Method from this
menu or by going into their respective menus.
1. Go into the setup mode by pressing the Service Button
on the IOB.
2. Select
Communications
.
3. Select
LeagueLeader Setup
.
4. Choose the
Communications Method.
You have three
choices: Ethernet, WiFi, or Modem (Internet). Each
Communications Method
will have different
settings.You can set them up now by going into their
respective settings menu right below Communications
Method.
5. Enter in your
LeagueLeader Account Settings
. Here
you will enter in your FTP Username and Password.
6. Once all settings are entered, including the Device
Settings, click on
Perform Update
to test the connec-
tion.
5. Plug in the Galaxy 3.
6. Go into the setup mode by pressing the Service Button
on the IOB.
7. Select
Communications
.
8. Select
Connection Setup
. Choose
WiFi Setup
.
9. Make sure
Enabled
is toggled “YES”.
10. Make sure
Internet
is toggled “YES”.
11.Click on
Access Point
. This will scan the local area for
any wireless access points.
12.Choose the access point you intend to use. Depending
on the area, more than one access point may be dis-
played. The signal strength and the security type will be
listed by each access point.
13.The
Security Type
should be automatically assigned.
14.Enter in the
Security Key
or
Pass Phrase
.
WEP uses an
Encryption Key
. The key is ten (10)
characters long and made out of the numbers 0-9 and
the letters a-h.
WPA and WPA2 can use an
Encryption Key
like
WEP, but they also have access to a
Passphrase
. This
Passphrase can be any combination of letters (upper
and lowercase) and numbers.
15.Select
IP Setting
.
Auto (DHCP) will automatically find all the internet
settings it needs.
Manual will require you to get the I.P. Address, Net
Mask and other internet settings yourself.
6.3 Setting up a Wireless Network
Setting up a wireless network is different than a wired net-
work. You will need to have a properly set up router first.
1. Unplug the Galaxy 3.
2. Unlock and open the bezel and monitor.
3. Plug in the wireless card on to the motherboard. See A1
(page 19) for our list of recommended Wireless Cards.
4. Secure the PCI Card to the bracket with a screw.
Wifi Card
Securing Screw
9. For ease of use, make sure
IP Setting
is set to
“Auto (DHCP)”. This will configure all the other
Internet settings for you.
10.Once setup, Return to Previous Menu.
11.Select
LeagueLeader Setup.
12.
Connection Method
should be already selected for
you, select
LeagueLeader Account Settings
.
13.Input your LeagueLeader FTP Settings.
14.Once all finished, select
Return to Previous Menu
.
15.Select
Perform Update.
6.2 Setting up a Wired Network
(Ethernet)
Setting up a wired network, or ethernet, is fairly straight
forward. The Galaxy 3’s mainboard has a built in network
card. You will need to have a properly set up router first.
1. Run an Ethernet cable from the router to the Galaxy 3.
2. Slide the Ethernet cable between the upper and lower
cabines in the back of the Galaxy 3.
3. Plug the Ethernet cable into the motherboard.
4. Go into the setup mode by pressing the Service Button
on the IOB.
5. Select
Communications
.
6. Select
Connections Setup
. Choose
Ethernet
.
7. Make sure
Enabled
is toggled “YES”.
8. Make sure
Internet
is toggled “YES”.
Содержание galaxy 3
Страница 36: ......
