Aquaread Aquaprobe AP-700 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 141

background image

Aquaprobe

®

AP-700, AP-800 & AP-2000 Instruction Manual

10401-00870 Rev R

The Aquaprobe

®

AP-2000 and AP-2000-D models are designed to be fully submerged in

water and are rated to IP68, that is to say, they are rated for continual immersion to a depth
of 30 meters, and short term immersion (less than 12 hours) to 100 meters.

2.3. Important Information about the Probe Sleeve & Sleeve End Cap

The Aquaprobe

®

is constructed with an aluminium sleeve surrounding the delicate sensing

electrodes. The Sleeve can be easily removed by unscrewing to allow cleaning of the
individual electrodes, however,

the Probe sleeve forms an integral, working part of the

Probe’s measurement system, and MUST be fitted for correct operation.

Probe sleeves are also specifically matched to the Probe with which they were
supplied. If you have more than one Aquaprobe

®

, be sure not to mix the sleeves up

between the Probes. Doing so may seriously affect the performance of the EC
electrode.

All Aquaread

®

Optical Electrodes are incredibly sensitive. For example, the Turbidity

electrode is capable of measuring between 0 and 3000NTU with an internal resolution of
greater than 0.1NTU. This means that the electrode is able to detect changes in turbidity
that are less than 0.003% of the full range! The other optical electrodes have a similar level
of sensitivity.

It follows, therefore, that in order to provide stable, repeatable readings, the environment in
which the measurements are made must be completely stable and repeatable.

For this reason, the Aquaprobe

®

is constructed with a matt black
aluminium sleeve and end cap
that enclose the sensing
electrodes and provide a closed,
constant condition, non reflective
measurement chamber.

This is essential for the
correct calibration and
operation of all types of
optical electrodes.

A diagram of the Aquaprobe’s
measurement chamber is shown
here.

In order to obtain consistent results, the measurement chamber created within the
Aquaprobe

®

must remain physically constant during both calibration and

measurement.

If the optical electrode is calibrated under one set of conditions then used to measure under
another set of conditions, the readings will naturally be erroneous, especially at low
concentrations.

A perfect example of this is calibrating with the end cap removed then measuring with the
end cap fitted (or vice-versa). By changing the physical characteristics of the measurement
chamber, you also change the calibration and response of the electrode.

© 2017 Aquaread

®

Ltd.

www.aquaread.com

Page 10 of 141

«
...
8
9
10
11
12
...
»

Содержание Aquaprobe AP-700














































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aquaprobe AP-700

Бренд: Keithley Страницы: 73

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: R.M. Young Страницы: 2

Бренд: Galileo Страницы: 19

Бренд: Galileo Страницы: 71

Бренд: La Crosse Technology Страницы: 8

HYGRASREG KH-30

Бренд: S+S Regeltechnik Страницы: 16

IRmadillo DOC1048R

Бренд: Keit Страницы: 27

Бренд: RS PRO Страницы: 44

Бренд: H. HERMANN EHLERS Страницы: 40

Бренд: King Instrument Страницы: 5

Бренд: Badger Meter Страницы: 32

Бренд: Frama Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды