Simpool Timer Model
INSTRUCTION AND MAINTENANCE MANUAL
Programmable digital peristaltic pump ENGLISH
ADSP7000722 rev. 1.0 23/02/2017
47/64
From the Settings Menu you can carry out the following operations (refer to
Figure 13
):
▪
Set the password to access the programming section
PAS
: with
Enter
you can go to the
“000” selection
page,
with the
▲
and
▼ keys you can increase/decrease the value displayed and with
Enter
you can scroll
to the figure you intend to set. After choosing the new password, press
Enter
for 3 seconds to go back to the
PAS
entry;
▪
Enable the pump stop in case of a
P.St
level alarm: to enter and exit the submenu, use the
Enter
key, use
the
▲
and
▼ keys to choose "YES/no";
▪
Programme the current day of the week
D.CL
: use
Enter
to enter and exit the submenu and use the
▲
and
▼ keys to scroll to the
Sun/Mon/Tue/Wed/Thu/Fry/Sat
values;
▪
Programme the hours of the current time
H.CL
: to enter and exit the submenu, use
Enter,
to scroll through
the values from 0 to 23 hours use the
▲
and
▼ keys;
▪
Programme the minutes of the current time
n.CL
: to enter and exit the submenu, use
Enter,
to scroll through
the values from 0 to 59 seconds use the
▲
and
▼ keys;
▪
Set the stabilization time of the inhibiting signal,
Stb
, coming from the swimming pool recirculation pump,
within a range of 0-999 seconds: to enter and exit the submenu, use
Enter
, to scroll through the values use
the
▲
and
▼ keys;
▪
Set the time of the pump maintenance alarm,
O.F.d
, from 0 (disabled) to 999 hours, based on the following
format:
-
h.mm
up to 9 h and 59 m
-
hh.m
up to 99 h and 59 m (minutes expressed in tens)
-
hhh
up to 999 h
To enter and exit the submenu use
Enter
and increase/decrease the value with the
▲
and
▼ keys;
▪
Access the
In.t
inhibiting signal recognition window: to enter and exit the submenu use
Enter
. The display
will show the status identified by the pump for the input signal:
Steady "HI"
: enabling signal identified as active;
Steady "Lo"
: enabling signal identified as not active;
Flashing “HI”:
enabling signal identified as active, but slightly above the identification voltage threshold;
Flashing "Lo":
enabling signal identified as not active, but slightly below the identification voltage threshold;
If the status displayed does not correspond to the actual status of the signal or if the status displayed is
flashing, just scroll with the
▲
and
▼ keys to change the threshold, namely:
Status of the non-active signal (recirculation pump OFF):
→
if the signal is identified as active (steady or flashing
HI
) or not active but near the threshold (flashing
Lo
),
press ▼ to reduce the threshold voltage until a steady “
Lo
” is displayed;
→
if the signal is permanently identified as not active (steady
Lo
), conduct a check when the signal is
activated;
Status of the non-active signal (recirculation pump ON):
→
if the signal is identified as not active (
Lo
steady or flashing), or active but near the threshold(flashing
HI
),
press
▲
to increase the threshold voltage until a steady “
HI
” is displayed;
→
if the signal is permanently identified as not active (steady
HI
), conduct a check when the signal is
disabled;
▪
Enable or disable the inhibiting sign
In.E
: to enter and exit the submenu, use the
Enter
key, use the
▲
and
▼ keys to choose "YES/no";
▪
Choose if you want to enable modification of the daily and weekly dosage calendar,
OnL
from the User
Menu: to enter and exit the submenu, use the
Enter
key, use the
▲
and
▼ keys to choose "YES/no";
▪
Set the wait time of the inhibiting signal
tn.A
, that is the time frame, from the scheduled dosage time, within
which it is necessary to receive the stabilized recirculation pump signal to activate the product dosage: to
enter and exit the submenu, use the
Enter
key, use the
▲
and
▼
keys to scroll through the values from 0 to
60 minutes;