Aqua Lung MISTRAL SECOND STAGE Скачать руководство пользователя страница 13

Страница: 13 / 18

Mistral Second Stage Technical Maintenance Manual

Table 3: Recommended Cleaners and Lubricants

LUBRICANT/CLEANER

APPLICATION

SOURCE

Christo-Lube

MCG 111

All o-rings

Aqua Lung, PN 820466, or
Lubrication Technologies

310 Morton Street

Jackson, OH 45640

(800) 477-8704

Oakite #31

Acid bath for reusable stainless steel and

brass parts.

Oakite Products, Inc.

50 Valley Road

Berkeley Heights, NJ 07922

White distilled vinegar

Acid bath for reusable stainless steel

and brass parts.

“Household” grade

Liquid dishwashing detergent

(diluted with warm water)

Degreaser for brass and stainless steel

parts; general cleaning solution for plastic

and rubber

“Household” grade

CAUTION:

Silicone rubber requires no lubrication or preservative

treatment. DO NOT apply grease or spray to silicone rubber parts.
Doing so may cause a chemical breakdown and premature deterioration of
the material.

CAUTION:

Do not use muriatic acid for the cleaning of any parts. Even

if strongly diluted, muriatic acid can harm chrome plating and may leave a
residue that is harmful to o-ring seals and other parts.

Содержание MISTRAL SECOND STAGE



















Результаты поиска

Содержание MISTRAL SECOND STAGE

Отзывы:

Бренды по названию

Популярные бренды

Aqua Lung MISTRAL SECOND STAGE, Техническое руководство по обслуживанию

Результаты поиска

Содержание MISTRAL SECOND STAGE

Отзывы:

Бренды по названию

Популярные бренды