Appsys ProAudio multiverter MVR-64 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 50

background image

User's Manual

Parameter

Value

PC port

USB 2.0 (FTDI 2232). Remote control and firmware update, no audio connection

RS485 port

Male D-Sub 9pin, Yamaha AD8HR compatible
Pinout: 2=RX-, 3=TX-, 4=TX+, 5=GND, 6=RX+

Extension port

HDMI connector type (not HDMI compatible).
64ch@32/44.1/48kHz, 32ch@64/88.2/96kHz, 16ch@128/176.4/192kHz

MADI optical port

SC connector, 50/125 µm or 62.5/125 µm multi-mode fiber (MM fiber),
1300nm, up to 2km total length.
Transceiver can be changed to Single mode (9/125µm) at the factory on request.
64ch@32/44.1/48kHz, 32ch@64/88.2/96kHz, 16ch@128/176.4/192kHz
56/57/64 channel support, all AES3 bits (U, C, V) preserved

MADI BNC port

Standard AES10 coaxial port. Use with up to 100meters of 75 ohm coaxial cable
64ch@32/44.1/48kHz, 32ch@64/88.2/96kHz, 16ch@128/176.4/192kHz
56/57/64 channel support, all AES3 bits (U, C, V) preserved

MADI TP port

AES-X 213 (upcoming MADI specification) compatible.
64ch@32/44.1kHz, 56ch@48kHz, 32ch@64/88.2, 28ch@96kHz,
16ch@128/176.4kHz, 14ch@192kHz
Pinout: MADI-TP on 4/5, 7/8
Alternative use: Second AES50 port, Pinout: Data on 4/5, 7/8; Sync on 1/2, 3/6 (adapter
cable required)
56/57/64 channel support, all AES3 bits (U, C, V) preserved

AES50 port

AES50 3.1 compatible
[email protected]/48kHz, [email protected]/96kHz
Pinout: Data on 1/2, 3/6; Sync on 4/5, 7/8
Alternative use: Second MADI-TP with Pinout: 1/2, 3/6 (adapter cable required)

Wordclock port

Output: 5.0Vpp nominal, able to drive two parallel 75 Ohm terminations
Input: 2.0Vpp...5.0Vpp

Dante/AES67 port

2x Gigabit Ethernet, configurable either as “Switch” or as “Redundant connection” in
the Dante controller. Device prefix: “MVR64”
64ch@32/44.1/48kHz, 32ch@64/88.2/96kHz, 16ch@128/176.4/192kHz

MIDI port

Standard isolated input, standard MIDI output
Data received on IN is passed unaltered to THRU

Headphones

2x125mW into 32Ohm (@0.01% THD+N)
Bandwidth: 22Hz to 22kHz

ESD protection

all ports: +/- 15kV (Human Body Model)

Table 6: Specifications

44

«
...
42
43
44
45
46
...
»

Содержание multiverter MVR-64



















































Отзывы:

Нет отзывов

Похожие инструкции для multiverter MVR-64

Бренд: SAJ Страницы: 68

Бренд: C&C TECHNIC Страницы: 2

Бренд: APsystems Страницы: 22

MONO MIXER SERIES

Бренд: Audioplex Страницы: 1

Бренд: SAJ Страницы: 26

Бренд: Lika Страницы: 2

Бренд: Cosel Страницы: 62

Бренд: Peachtree Audio Страницы: 56

Бренд: Sungrow Страницы: 136

Бренд: N-Tron Страницы: 2

Бренд: N-Tron Страницы: 40

Бренд: Baumer Страницы: 36

Бренд: Senci Страницы: 39

Multi-Decoder MD-2

Бренд: tams elektronik Страницы: 40

Бренд: TANDBERG Страницы: 196

Бренд: Mobotix Страницы: 44

Бренд: Peak Страницы: 37

5.1 AV Switch Box

Бренд: Jaton Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды