Applied Biosystems 7300 Скачать руководство пользователя страница 22

Страница: 22 / 174

Safety and EMC Compliance Information

Chemical Waste Safety

xxii

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Chemical Safety

Guidelines

To minimize the hazards of chemicals:

• Read and understand the Material Safety Data Sheets (MSDSs) provided by the

chemical manufacturer before you store, handle, or work with any chemicals or
hazardous materials. (See

“About MSDSs”

page xxi

• Minimize contact with chemicals. Wear appropriate personal protective equipment

when handling chemicals (for example, safety glasses, gloves, or protective
clothing). For additional safety guidelines, consult the MSDS.

• Minimize the inhalation of chemicals. Do not leave chemical containers open. Use

only with adequate ventilation (for example, fume hood). For additional safety
guidelines, consult the MSDS.

• Check regularly for chemical leaks or spills. If a leak or spill occurs, follow the

manufacturer’s cleanup procedures as recommended on the MSDS.

• Comply with all local, state/provincial, or national laws and regulations related to

chemical storage, handling, and disposal.

Chemical Waste Safety

Chemical Waste

Hazard

HAZARDOUS WASTE.

Refer to Material Safety Data Sheets and

local regulations for handling and disposal.

CHEMICAL WASTE HAZARD.

Wastes produced by Applied

Biosystems instruments are potentially hazardous and can cause injury, illness, or death.

CHEMICAL STORAGE HAZARD.

Never collect or store waste

in a glass container because of the risk of breaking or shattering. Reagent and waste

bottles can crack and leak. Each waste bottle should be secured in a low-density

polyethylene safety container with the cover fastened and the handles locked in the

upright position. Wear appropriate eyewear, clothing, and gloves when handling reagent

and waste bottles.

Chemical Waste

Safety Guidelines

To minimize the hazards of chemical waste:

• Read and understand the Material Safety Data Sheets (MSDSs) provided by the

manufacturers of the chemicals in the waste container before you store, handle, or
dispose of chemical waste.

• Provide primary and secondary waste containers. (A primary waste container holds

the immediate waste. A secondary container contains spills or leaks from the
primary container. Both containers must be compatible with the waste material and
meet federal, state, and local requirements for container storage.)

• Minimize contact with chemicals. Wear appropriate personal protective equipment

when handling chemicals (for example, safety glasses, gloves, or protective
clothing). For additional safety guidelines, consult the MSDS.

Содержание 7300















































































































































































Результаты поиска

Содержание 7300

Отзывы:

Похожие инструкции для 7300

Бренды по названию

Популярные бренды

Applied Biosystems 7300, Руководство по установке и обслуживанию

Результаты поиска

Содержание 7300

Отзывы:

Похожие инструкции для 7300

Бренды по названию

Популярные бренды