Applied Biosystems 7300 Скачать руководство пользователя страница 91

Страница: 91 / 174

Chapter 5

Performing the Background Calibration and Optical Calibration

Troubleshooting

Applied Biosystems 7300/7500/7500 Fast Real-Time PCR System Installation and Maintenance Guide

Notes

4. Locate the contaminated well position(s) by selecting

successively fewer wells in the plate document.

The items that follow show an example of how to determine
the location of a contaminated well.

a. In the Spectra tab, select columns 1-6. The raw data from

the selected wells does not include the irregular peak.
Therefore, the contaminated well must be in columns 7-12.

b. Select columns 7-9. The raw data from the selected wells

includes the irregular peak. The contaminated well must be
in columns 7-9.

c. Select wells in row E and below in columns 7-9. The raw

data from the selected wells does not include the irregular
peak. The contaminated well must be in the first four wells
of columns 7-9.

d. Finally, by selecting each of the wells from the first four

wells of columns 7-9, you can determine the location of the
contaminated well (B9).

5. Repeat

step 4

until you identify the location of each

contaminated well.

Troubleshooting – Background Calibration

Contaminated well
is not displayed

Contaminated
well

Contaminated
well is not
displayed

Contaminated
well

Содержание 7300















































































































































































Результаты поиска

Содержание 7300

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 7300, Руководство по установке и обслуживанию

Результаты поиска

Содержание 7300

Отзывы:

Бренды по названию

Популярные бренды