AOpen ISDN SOHO Router Скачать руководство пользователя

Страница: 23 / 89

ISDN Router Manual V.1.1

At this point the unit is configured. It is suggested to save the configuration immediately to keep it

in the EPROM. The user can connect and start surfing the internet by entering the following

command.

By using

qconfig

you can change the telephone number and connect to any specified destination or

ISP manually. For detailed significance of the above command, please see the following command

set.

Note: The quick configuration can only be executed in CLI mode.

Quick Configuration Setup (ESC, ESC to exit)

--------------------------------

IP address of this unit's LAN port : 123.97.35.7

IP mask of this unit's LAN port : 255.255.255.0

Switch Type (etsi, ni1, ntt) : ni1

DN1

: 3930219

DN2

: 3930237

SPID1

: 50839302190101

SPID2

: 50839302370101

Phone number of the remote unit : 8398111

User's ID to log into remote site

: john

User's password to log into remote site

: master

CLI>

config save

CLI>

connect john

(

user entered

)

CLI> B1 channel up (

automatic display by router

)

CLI> add net (

automatic display by router

)

CLI>

config ip nat add isdn

(

user entered

)

Содержание ISDN SOHO Router


























































































Результаты поиска

Содержание ISDN SOHO Router

Отзывы:

Похожие инструкции для ISDN SOHO Router

Бренды по названию

Популярные бренды

AOpen ISDN SOHO Router, Руководство пользователя

Результаты поиска

Содержание ISDN SOHO Router

Отзывы:

Похожие инструкции для ISDN SOHO Router

Бренды по названию

Популярные бренды