AOpen ISDN SOHO Router Скачать руководство пользователя

Страница: 13 / 89

ISDN Router Manual V.1.1

2.3 Bottom Plate

Battery Backup

The battery backup solution a supporting device when there’s a sudden power loss. A total of 6 AA

batteries are required to backup the router.

Please make sure that all 6 batteries are placed

correctly.

Battery Mode Operation

In case of sudden loss of power, the router switches to battery backup mode automatically. ( with all

6 batteries correctly installed)

Please note that in the power backup mode, only the analog ports

can function normally.

In battery backup mode, with the brand new regular batteries, the router can last at least 3 hours in

standby or can run one analog port continuously for about 2 hours.

Changing Batteries

Please check the battery if the router does not function normally in battery backup mode. If the

battery is low, please replace them. A user is suggested to replace all 6 batteries together.

2.4 Accessory

The accessory may be different in different markets or by customer requirements. Please check

with the local dealer for accessory information.

♦

router main unit

♦

RS232 cable

♦

RJ11 cable for connecting to ISDN U-line

♦

Diskette or CD ROM (including Win NT/95/98 configure software and INF file)

♦

User‘s manual

When opening the package, make sure it contains all the above items in good order. If any of

the accessories was damaged, please contact your dealer immediately.

Содержание ISDN SOHO Router


























































































Результаты поиска

Содержание ISDN SOHO Router

Отзывы:

Похожие инструкции для ISDN SOHO Router

Бренды по названию

Популярные бренды

AOpen ISDN SOHO Router, Руководство пользователя

Результаты поиска

Содержание ISDN SOHO Router

Отзывы:

Похожие инструкции для ISDN SOHO Router

Бренды по названию

Популярные бренды