Ankom 2000 Скачать руководство пользователя

Страница: 34 / 44

Operator’s Manual

pg. 34

Rev 05/12/21

Select Crude Fib

<Enter>

Insert Samples
Close Lid<Enter>

Hot Water On

<Start>

Check the Temperature Control using the Boil Test

To check the ANKOM

2000

Fiber Analyzer temperature control, do a Boil Test

once per month

as specified in the

procedure below.

Disconnect cubitainers if connected.

Fill a pitcher with approximately 2L of hot water (50 ˚C or above) and set aside for later.

Turn on the instrument. Remove the bag suspender from the vessel.

on the display, press the

ENTER

button.

When you see

on the display, press the

ENTER

button.

When you see

(

Do not

insert samples.

Do not

close lid.)

on the display, press the

START

button.

When you see

Record Voltage:

Record the voltage shown on the display before pouring in the water. _______V

(Should be between 5-10 VDC)

Pour the 2L of hot water into the digestion vessel so that the
glass level sensor tip is under water.

Record the voltage after pouring in the water. _______V

(Should be between 0-3 VDC)

Agitation and heat begin automatically.

Do not close the lid. Occasionally stir the water to ensure uniform heating.

The water should begin to boil in 5-15 minutes.

When a strong boil is reached, stir the water in the vessel and record:

The temperature on the controller. _______˚C

The temperature on a calibrated thermometer. _______˚C
(Place the thermometer near the probe at the bottom of the vessel.)

The temperature shown on the display. _______˚C

If these three temperatures are not within ½ degree of each other, contact
ANKOM Technology for assistance. Send results to [email protected].

Level Sensor Tip

Controller

Calibrated
Thermometer

Temperature Probe

Содержание 2000













































Результаты поиска

Содержание 2000

Отзывы:

Похожие инструкции для 2000

Бренды по названию

Популярные бренды

Ankom 2000, Руководство оператора

Результаты поиска

Содержание 2000

Отзывы:

Похожие инструкции для 2000

Бренды по названию

Популярные бренды