andrews MAXXflo EVO CWH 30/201 Скачать руководство пользователя страница 73

Страница: 73 / 76

Maintenance

MAXXﬂ o EVO

6.5 ERROR CODES (CONTINUED)

Error

Code

Error Code Description

Diag.

Code

Notes

110

SLT Lockout

306 431

432 433

434 435

436 756

Electronic temperature limits exceeded. General overheating

issue. Check for pump operation, trapped air and heat ex-

changer blockages. Monitor temperatures of system to estab-

lish problem area.

429 818 Criteria for the safe reset of the error sub code 433 (see

above) has not been met. Allow the boiler to cool further be-

fore pressing reset again

305 412

550 551

754

Overheat protection circuit is open circuit (X18 STB). Check

connector is pushed fully onto control PCB

428 438

817

Maximum Delta T of system exceeded. Check pump opera-

tion and presence of trapped air in the heat exchanger. Flow

through heat exchanger may be restricted.

426 437

815

Flow temperature heat up gradient exceeded. Check pump

operation and presence of trapped air in the heat exchanger.

Flow through heat exchanger may be restricted.

427 816 Criteria for the safe reset of the error sub code 426 (see

above) has not been met. Allow the boiler to cool further be-

fore pressing reset again

420 421

819 820

Return temperature greater than ﬂ ow temperature. Check that

the ﬂ ow and return sensors are operating correctly

419 430

813 814

Flow temperature limit exceeded. Check for overheating is-

sues and ﬂ ow sensor (B2) performance.

809 810

422 423

Flow temperature reading error. Temperature reading less

than 0

C or greater than 124

C . Check ﬂ ow sensor (B2) and

replace if necessary.

425

812

Return temperature limit exceeded. Check for overheating is-

sues and return sensor (B7) performance.

424

811

Return temperature reading error. Temperature reading less

than 0

C or greater than 124

C . Check ﬂ ow sensor (B7) and

replace if necessary.

111

Shutdown limit thermostat

Any

Heat exchanger temperatures have been exceeded. Investi-

gate ﬂ ow rates and controls to determine causes of temporary

fault code.

125

Maximum boiler temperature

exceeded

Any

Flow temperatures have been exceeded. Appliance will

continue once temperatures have dropped below maximum

allowed limits.

126

DHW charging temperature

not reached

Any

Charging temperature never achieved. Check operation and

heat up times for DHW

127

DHW legionella temperature

not reached

Any

Check operation of legionella function and DHW system.

Legionella setpoint has not been achieved within 48 hours of

the legionella function operating. If using a secondary return

system and sensor, do not set the legionella function setpoint

too high, as the heat losses around the hot water pipework

may not permit this setpoint to be achieved

128

Loss of ﬂ ame during opera-

tion

394

Flame lost in operation within the ﬁ rst 7 seconds of the start

of the modulation phase. Check the CO

is set correctly and

check operation and condition of ionisation electrode.

854

Flame lost in operation after the ﬁ rst 7 seconds of the start

of the modulation phase. Check the CO

is set correctly and

check operation and condition of ionisation electrode.

625

Flame lost in operation more than 24 times in a 24 hour pe-

riod. Check the preceding error codes for details on when the

ionisation current was lost. Check the operation of the ionisa-

tion electrode, gas supply, and ﬂ ue system. Check that there is

suﬃ cient gas available to the heater at all times.

Содержание MAXXflo EVO CWH 30/201













































































Результаты поиска

Содержание MAXXflo EVO CWH 30/201

Отзывы:

Похожие инструкции для MAXXflo EVO CWH 30/201

Бренды по названию

Популярные бренды

andrews MAXXflo EVO CWH 30/201, Руководство по установке и обслуживанию

Результаты поиска

Содержание MAXXflo EVO CWH 30/201

Отзывы:

Похожие инструкции для MAXXflo EVO CWH 30/201

Бренды по названию

Популярные бренды