andrews MAXXflo EVO CWH 30/201 Скачать руководство пользователя страница 55

Страница: 55 / 76

Maintenance

MAXXﬂ o EVO

6.2 REMOVING AND CHANGING COMPONENTS

NONE OF THE CONTROLS ARE REPAIRABLE . IF THEY ARE NOT FUNCTIONING THEY MUST BE
REPLACED In all cases, before work commences turn o

ﬀ

the mains electricity and gas supply.

The following items do not require isolating water before removal:

•

DHW tank temperature sensor (B3)

•

Flue temperature sensor (B8)

•

AVS37 GUI display

•

LMS14 PCB Replacement

•

Spark generator

•

Combustion fan

•

Overheat thermostat

•

Gas valve

•

Electrode removal

•

Back ﬂ ow prevention ﬂ ue valve

The following items require isolation of water before removal and bleeding air afterwards:

•

Heat exchanger

•

Circulation pump

See the following sections for an explanation on how to change these components:

6.2.1 DHW TANK TEMPERATURE SENSOR (B3)

• Remove and withdraw the foam insulation above the top of the tank
• Gently pull the sensor up the dip tube

• Undo the bulkhead seal and pull the sensor through to the front.

• Unplug connector from loom.

• Cut oﬀ securing tie and remove sensor.
• Replacement is the reverse.

Bulkhead seal

Sensor

Remove cable tie

Sensor connector

Содержание MAXXflo EVO CWH 30/201













































































Результаты поиска

Содержание MAXXflo EVO CWH 30/201

Отзывы:

Похожие инструкции для MAXXflo EVO CWH 30/201

Бренды по названию

Популярные бренды

andrews MAXXflo EVO CWH 30/201, Руководство по установке и обслуживанию

Результаты поиска

Содержание MAXXflo EVO CWH 30/201

Отзывы:

Похожие инструкции для MAXXflo EVO CWH 30/201

Бренды по названию

Популярные бренды