andrews MAXXflo EVO CWH 30/201 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 76

background image

Maintenance

60

MAXXﬂ o EVO

6.2.10 BACK FLOW PREVENTION VALVE

•

Remove the 8 Torx screws holding the cover plate onto the air arm and gently pull cover away from the seal.

•

The Back Flow Prevention Valve (BFPV) is located inside the cover itself and can be slid out for inspection.

•

Inspect BFPV for damage and operation. Replace if necessary

•

Inspect air arm seal for damage. Replace if necessary

•

Assembly is the reverse

6.2.11 CIRCULATION PUMP (Q1)

•

Close the shut oﬀ valve before the pump, or if optional pressure sensor kit ﬁ tted close oﬀ the shut oﬀ valves
either side of the pump

•

Drain oﬀ water from the DHW tank (approximately 30 litres) or if the optional pressure sensor kit is ﬁ tted use
the drain points between the shut oﬀ valves

•

Remove the PWM and power connectors, using a small ﬂ at blade screwdriver to lift the white tab before
pulling each connector free.

•

Undo the unions at the top and bottom of the pump body and remove pump.

•

Fit the new pump seals

•  Replacement is the reverse
•  Reﬁ ll and bleed of air
•  Operate the pump by pulling the electrical connector oﬀ  the heat exchanger front ﬂ ow sensor (B2)

When all sound of air has stopped, reconnect B2 sensor and press the reset for 1s

Pump Union

Pump Union

Flow Sensor (B2)

F

F

«
...
58
59
60
61
62
...
»

Содержание MAXXflo EVO CWH 30/201













































































Отзывы:

Нет отзывов

Похожие инструкции для MAXXflo EVO CWH 30/201

Бренд: D-D The Aquarium Solution Страницы: 8

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 26

Бренд: Fagor Страницы: 4

Бренд: Fagor Страницы: 12

Бренд: Lasko Страницы: 8

Бренд: Radialight Страницы: 10

Бренд: Midea Страницы: 36

Бренд: Homa Страницы: 11

RainStation RS-0001

Бренд: EarthMinded Страницы: 16

Бренд: T.I.P. Страницы: 136

Бренд: Quantum Страницы: 36

Бренд: Faber Страницы: 9

Бренд: DanPure Страницы: 8

Cylinder Passport

Бренд: WarmFlow Страницы: 16

Бренд: Easy@Home Страницы: 38

Бренд: DAB Страницы: 228

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды