manualshive.com logo in svg

Andor Technology Zyla sCMOS 4.2 PLUS, Руководство по оборудованию

Поделиться
Скачать
Andor Technology Zyla sCMOS 4.2 PLUS Скачать руководство пользователя страница 73

version 2.0 rev 18 Feb 2021

73

Footnotes

1.  Figures are typical unless otherwise stated.
2.  Readout noise is for the entire system and is taken as a median over the sensor area excluding any regions of blemishes. It is a combination of sensor 

readout noise and A/D noise.

3. 

Quantum efficiency of the sensor at 20°C as supplied by the manufacturer.

4.  Dark current measurement is taken as a median over the sensor area excluding any regions of blemishes. 
5.  Linearity is measured from a plot of Signal vs. Exposure Time, in accord with EMVA 1288 standard. 
6. 

Software Exposure Events provide rapid software notification (SDK only) of the start and end of acquisition, useful for tight synchronization to moving 

peripheral devices e.g. Z-stage.

7.  ‘Global Clear’ is an optional keep clean mechanism that can be implemented in rolling shutter mode, which purges charge from all rows of the sensor 

simultaneously, at the exposure start. The exposure end is still rolling shutter. It can be used alongside the Fire All output of the camera and a pulsed 

light source to simulate Global Exposure mechanism, albeit less efficiently than the true Global Shutter exposure mode of Zyla 5.5. Furthermore Global 

Clear differs from true Global Shutter in that it can only be used in ‘non-overlap’ readout mode, i.e. sequential exposure and readout phases rather than 

simultaneous. 

8. 

Zyla USB 3.0 models should work with any modern USB 3.0 enabled PC/laptop (provided hard drives or RAM is sufficient to support data rates) as every 

USB 3.0 port should have its own host controller. Zyla USB 3.0 models also ship with a USB 3.0 PCI card as a means to add a USB 3.0 port to an older PC, 

or as a diagnostic aid to interoperability issues or to ensure maximum speed.

Mechanical Specifications

Zyla 4.2 PLUS and Zyla 5.5 models

Weight (Camera Only*)

1 kg (2 lb 3 oz)

Weight (External Power Supply)

0.33 kg (0 lb 11.6 oz)

* The camera weight is the head only with no cables or pipes attached and without water or coolant.

Environmental Specifications

Zyla 5.5

Zyla 4.2 PLUS

Location to be used

Indoor

Altitude

Up to 2000 m

Operating temperature

0ºC to 30ºC ambient

0ºC to 27ºC ambient

Storage temperature

-10ºC to 50ºC

Operating relative humidity

 < 70% (non-condensing)

Pollution degree

Pollution degree 2. Normally only non-conductive pollution occurs. Occasionally, however, a 

temporary conductivity caused by condensation must be expected.

Ingress protection rating

IP20

Electromagnetic compatibility

This is a Class A product. In a domestic environment this product may cause 

electromagnetic interference, in which case the user may be required to take adequate 

measures

Cooling vent clearance

100 mm minimum

Содержание Zyla sCMOS 4.2 PLUS















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды