manualshive.com logo in svg

Andor Technology Zyla sCMOS 4.2 PLUS, Руководство по оборудованию

Поделиться
Скачать
Andor Technology Zyla sCMOS 4.2 PLUS Скачать руководство пользователя страница 63

version 2.0 rev 18 Feb 2021

63

4.2   Using the Lens Mount Adaptors

The Zyla has a T-mount thread as standard. There are 3 standard lens mount adaptors available that can be 

specified at the time of ordering, enabling the Zyla to suit standard mounting options. These are as follows:

•

C-mount

•

CS-mount

•

F-mount

The Zyla is supplied with the selected lens mount adaptor locked into a 

nominal position of 1 mm

 from the 

top surface of the Zyla faceplate (see 

Figure 37

). Adaptors can be removed, inserted and adjusted (for focus 

optimization) as required.

Figure 39: 

Lens mount adaptor fitted to Zyla (In this example a CS-mount adaptor is shown).

4.2.1 C-mount Adaptor

The C-mount adaptor can be adjusted as follows:

1. Loosen the 2 locking screws located in the front face of the adaptor if required using supplied 1.5

mm Allen key.

Figure 40: 

C-mount adaptor

2. Manually screw the C-mount into position until the desired focus is achieved. It must not be

screwed the entire way into the faceplate.

3. Lock the C-mount into position using the 2 locking screws and 1.5 mm Allen key. 

NOTE: Maximum

torque applied must not exceed: 0.6 Nm

Lens mount adaptor set 
at nominal position 1 mm 
from top surface of the 
Zyla faceplate.

Lens mount 
adaptor

Zyla

C-mount
locking screw
locations

Содержание Zyla sCMOS 4.2 PLUS















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды