manualshive.com logo in svg

Andor Technology Zyla sCMOS 4.2 PLUS, Руководство по оборудованию

Поделиться
Скачать
Andor Technology Zyla sCMOS 4.2 PLUS Скачать руководство пользователя страница 54

version 2.0 rev 18 Feb 2021

54

2.7.4.1  Live Mode

Live Mode

 refers to a version of 

Run Till Abort

 in which each user frame will be the latest frame output by the 

sensor and will have the minimum amount of latency through the camera as possible.

Live mode requires the use of SW Trigger. In order to ensure that frames are buffered in the on-camera memory 

for the shortest possible time, the next SW trigger must not be sent until the user frame has been transmitted 
from the camera. This ensures that the on-camera memory only stores a single user frame at a time and no 
additional latency builds up. 

NOTE: The frame rate achievable in Live Mode is dependent on the performance of the system that the 
camera is attached to.

2.7.5 Fast Exposure Switch 

During an acquisition the user can change the exposure time, within allowable limits. Once a new exposure 
value has been written, it will be applied to the next user frame after the current frame exposure has 

completed. The exposure time can be changed any number of times before the acquisition finishes

2.7.6 Frame Rate Control 

If Internal Trigger is being used, the camera will trigger the sensor at the fastest possible rate by default. The 

user can reduce this trigger rate by defining a Frame Rate that is less than the maximum possible rate. Frame 

Rate must be set before the acquisition starts.

Note: This is currently only applicable to ‘long exposures’.

2.7.7  LightScan PLUS

LightScan PLUS describes a functionality of the Zyla 4.2 PLUS camera that allows the end-user to have more 
control over the Rolling Shutter scanning mechanism that is inherent to CMOS sensors. This scanning mode can 
be readily adapted to niche optical modalities, such as Scanned Light Sheet microscopy or Line Scan Confocal 
Microscopy.

2.7.7.1 Multiple Readout Directions

The standard mode of operation in sCMOS cameras is to read out from the centre of the sensor out to the 
edge with two halves of the sensor exposing simultaneously. LightScan PLUS provides the user with a range 

of different rolling shutter readout options. Firstly, the rolling shutter can now be scanned from the top to the 

bottom of the sensor or vice versa in one continuous sweep (Figure 34), adapting the sensor to single port 
readout. It should be acknowledged however that this functionality will halve the rolling shutter frame rate, 
resulting in a maximum full resolution frame rate of 50 fps.

Figure 34: LightScan PLUS enables the rolling shutter to scan the sensor from top to bottom or vice versa in one continuous sweep. This 

is also known as Single Port Readout.

Содержание Zyla sCMOS 4.2 PLUS















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды