Analog Devices adsp-2100 Скачать руководство пользователя | Manualshive

Страница: 91 / 486

background image

4

Data Transfer

4 – 3

The address generators support both linear addressing and circular
addressing. The value of the L register corresponding to an I register (for
example, L0 would correspond to I0) determines which addressing scheme is used
for that I register. For circular buffer addressing, the L register is initialized
with length of the buffer. For linear addressing, the modulus logic is
disabled by setting the corresponding L register to zero.

Each time an I register is selected, the corresponding L register provides
the modulus logic with the length information. If the sum of the M register
and the I register crosses the buffer boundary, the modified I register
value is calculated by the modulus logic using the L register value.

All data address generator registers (I, M, and L registers) are loadable
and readable from the lower 14 bits of the DMD bus. Since I and L register
contents are considered to be unsigned, the upper 2 bits of the DMD bus
are padded with zeros when reading them. M register contents are signed;
when reading an M register, the upper 2 bits of the DMD bus are sign-
extended.

4.2.2

Indirect Addressing

The ADSP-2100 family processors allow two addressing modes for data
memory fetches: direct and register indirect. Indirect addressing is
accomplished by loading an address into an I (index) register and
specifying one of the available M (modify) registers.

The L registers are provided to facilitate wraparound addressing of
circular data buffers. A circular buffer is only implemented when an L
register is set to a non-zero value. For linear (i.e. non-circular) indirect
addressing, the L register corresponding to the I register used must be set
to zero.

Do not assume that the L registers are automatically initialized or may be
ignored; the I, M, and L registers contain random values following processor
reset. Your program must initialize the L registers corresponding to any I
registers it uses.

4.2.2.1 Initialize L Registers To 0 For Non-Circular Addressing

Setting an L register to a non-zero value activates the processor’s circular
addressing modulus logic. For linear indirect addressing you must set the
appropriate L register to zero to disable the modulus logic.

«
...
89
90
91
92
93
...
»

Содержание adsp-2100







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для adsp-2100

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: Paradyne Страницы: 12

Бренд: XESS Страницы: 23

Бренд: Maxim Страницы: 26

Бренд: Freescale Semiconductor Страницы: 921

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: Aaeon Страницы: 61

Бренд: ZiLOG Страницы: 11

Бренд: 3Com Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды