Analog Devices adsp-2100 Скачать руководство пользователя | Manualshive

Страница: 326 / 486

background image

15

Instruction Set Reference

15 – 3

The 24-bit instruction word allows a high degree of parallelism in
performing operations. The instruction set allows for single-cycle
execution of any of the following combinations:

• any ALU, MAC or Shifter operation (conditional or non-conditional)
• any register-to-register move
• any data memory read or write
• a computation with any data register to data register move
• a computation with any memory read or write
• a computation with a read from two memories.

The instruction set allows maximum flexibility. It provides moves from
any register to any other register, and from most registers to/from
memory. In addition, almost any ALU, MAC or Shifter operation may be
combined with any register-to-register move or with a register move to or
from either internal or external memory.

15.3

INSTRUCTION TYPES & NOTATION CONVENTIONS

The ADSP-2100 family instruction set is grouped into the following
categories:

• Computational: ALU, MAC, Shifter
• Move
• Program Flow
• Multifunction
• Miscellaneous

Because the multifunction instructions best illustrate the power of the
processors’ architecture, in the next section we begin with a discussion of
this group of instructions.

Throughout this chapter you will find tables summarizing the syntax of
the instruction groups. The following notation conventions are used in
these tables and in the reference page for each instruction.

Square Brackets [ ]

Anything within square brackets is an optional

part of the instruction statement.

Parallel Lines | |

Lists of operands are enclosed by vertical parallel

bars. One of the operands listed must be chosen.
If the parallel bars are within square brackets,
then the operand is optional for that instruction.

«
...
324
325
326
327
328
...
»

Содержание adsp-2100







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для adsp-2100

Бренд: Magnat Audio Страницы: 2

Бренд: Magma Страницы: 2

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Linear SCP-LT8362-S-EVALZ

Бренд: Analog Devices Страницы: 8

Бренд: Belkin Страницы: 72

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

Бренд: Supermicro Страницы: 16

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: Campbell Страницы: 38

Бренд: peplink Страницы: 2

Бренд: mikroElektronika Страницы: 2

Бренд: AXIOMTEK Страницы: 2

See3CAM 30 Z10X

Бренд: e-con Systems Страницы: 14

Acme Packet 3900

Бренд: Oracle Страницы: 70

LinkStation 500

Бренд: Buffalo Страницы: 139

Digital Loudspeaker

Бренд: Dolby Laboratories Страницы: 4

Бренд: ENERMAX Страницы: 33

Бренд: FOR-A Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды