Analog Devices adsp-2100 Скачать руководство пользователя | Manualshive

Страница: 216 / 486

background image

10

Memory Interface

10 – 3

10.2

PROGRAM MEMORY INTERFACE

This section describes the program memory interface of all ADSP-21xx
processors except the ADSP-2181.

The processors address 16K of 24-bit wide program memory, up to 2K
on-chip and the remainder external, using the control lines shown in
Figure 10.1. The processors supply a 14-bit address on the program
memory address bus (PMA) which is driven off-chip on the address bus in
the case of external program memory accesses. Instructions or data are
transferred across the 24-bit program memory data (PMD) bus which is
also multiplexed off-chip. For a dual off-chip data fetch, the data from
program memory is read first, then the data memory data. A program
memory select pin,

PMS

, indicates that the address bus is being driven

with a program memory address and memory can be selected.

Two control lines indicate the direction of the transfer. Memory read (

RD

)

is active low signaling a read and memory write (

WR

) is active low for a

write operation. Typically, you would connect

PMS

to

CE

(Chip Enable),

RD

to

OE

(Output Enable) and

WR

to

WE

(Write Enable) of your memory.

10.2.1 External Program Memory Read / Write

On-chip memory accesses do not drive any external signals.

PMS

,

DMS

,

RD

, and

WR

remain high (deasserted); the address and data buses are

tristated. Off-chip program memory access happens in this sequence:

1. The processor places the address on the PMA bus, which is

multiplexed off-chip, and

PMS

is asserted.

2.

RD

or

WR

is asserted.

3. Within a specified time, data is placed on the data bus, multiplexed to

the internal PMD bus.

4. The data is read or written and

RD

(or

WR

) is deasserted.

5.

PMS

is deasserted.

The basic read and write cycles are illustrated in Figure 10.2 on the next
page. Figure 10.2A shows zero wait states and 10.2B shows the effect of
one wait state.

«
...
214
215
216
217
218
...
»

Содержание adsp-2100







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для adsp-2100

Бренд: Lanner Страницы: 59

Бренд: Supero Страницы: 53

CL-SOM-AM57 Series

Бренд: CompuLab Страницы: 79

Бренд: Renesas Страницы: 40

Бренд: AES Страницы: 44

Бренд: Dantel Страницы: 22

DTS 4020.timebridge

Бренд: Mobatime Страницы: 94

PC/104-PCMCIA-1

Бренд: Kontron Страницы: 20

SteelCentral AppResponse 2170

Бренд: Riverbed Страницы: 166

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 2

Бренд: ADTRAN Страницы: 4

Бренд: ADTRAN Страницы: 4

NetVanta Series

Бренд: ADTRAN Страницы: 7

NetVanta 2000 Series

Бренд: ADTRAN Страницы: 15

Бренд: ADTRAN Страницы: 14

Бренд: ADTRAN Страницы: 85

Бренд: ADTRAN Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды