background image

39

2.  SINGLE PUSH BUTTON

 
 

To activate the power option, push the button once and hold 
until the desired position is achieved, then release. To return 
toward the neutral position, push the button a second time. 

3.  DUAL PUSH BUTTON

 

To activate the power option, push the button, located furthest 
from the wire, hold until the desired position is achieved and 
release. To return toward the neutral position, push the other 
button.

MULTIPLE POWER ACTIVATION

The following devices are designed to activate more than 
one power seating options described previously, such as tilt, 
elevate, recline, elevating & articulating legrests and elevating 
& articulating center mount. Activation devices are located next 
to the joystick. For the purpose of consistency, let’s assume the 
wheelchair is in its neutral position to start.

1.  4 OR 5 PUSH BUTTONS

 

 

NOTE

 – The power seating options are assigned at the factory 

according to the wheelchair configuration and depending on 
the options selected. 

 

To activate a power option, push the assigned button and 
hold until the desired position is achieved and release. 
Pushing the same button a second time, will activate the 
power option in the opposite direction toward the  
neutral position.

2.  4-WAY TOGGLE

 

 NOTE

 – This toggle switch can be pre-programmed  

with 2, 3 or 4 power seating options. 

 

If 2 power options are selected, these options will be 
assigned to the forward and backward toggle directions.

 

If 3 power options are selected, the third option will be 
assigned to the right side toggle. The fourth option will be 
assigned to the left side.  

 

To active a power option, toggle toward the assigned 
direction, hold until the desired position is achieved and 
release. If you toggle in the same direction a second time, it 
will activate the power option in the opposite direction. This 
applies to all power options.

3.  MULTI TOGGLE SWITCH

 

NOTE

 – Each side to every toggle is pre-programmed with 

an assigned power seating option according to the power 
options selected. Up to 5 power seating options can be pre-
programmed.

 

To activate a power option, toggle to one side and hold until 
the desired position is achieved then release. Toggle to the 
same side a second time and the power option will move 
in the opposite direction toward the neutral position. This 
applies to all power options.

Содержание ALLTRACK M3





















































Отзывы: