AMTAST EC910 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 53

AMTAST EC910 Скачать руководство пользователя страница 2

EC910 Portable Multiparameter Water Quality Meter

1

Introduction

Thank you for selecting the AMTAST EC910 portable multiparameter water quality meter. This manual provides a

-by-step guide to help you operate the

meter, please carefully read the following instructions before use.

UNPACKING THE METER:
Before unpacking, ensure that the current work environment meet following conditions.

●

Relative humidity is less than 80%.

●

Ambient temperature is greater than 0

o

C and less than 60

o

C.

●

No potential electromagnetic interference.

The following list describes the standard accessories of the meter. After the unpacking, please check all accessories are complete. If any are damaged or
missing, please contact nearest distributor.

ACCESSORIES:

●

pH Electrode

●

Conductivity Electrode

●

Dissolved Oxygen Probe

●

Temperature Probe

●

pH Buffer Pouches (pH4.01/7.00/10.01)

●

Conductivity Calibration Solutions (84µS/cm, 1413µS/cm, 12.88mS/cm)

●

Electrolyte Solution

●

Membrane Cap

pH Electrode

Conductivity Electrode

Dissolved Oxygen Probe

Temperature Probe

pH Buffer Pouches

Conductivity Calibration Solutions

Membrane Cap

Electrolyte Solution

DO

Electrolyte

Solution

Very Important:

If meter shows battery low, please stop use and change the battery ASAP, if you still use it, and meter

power off automatically, it will lost the system and need RETURN to us for install the system again.

The LCD will be blank and display nothing!!!

«
1
2
3
4
...
»

Содержание EC910






















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды