AMF Reece 101 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 60

AMF Reece 101 Скачать руководство пользователя страница 39

e-mail: [email protected]; [email protected] ; website: www.amfreece.com
Phones: +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606

Revised 09/2004

S-101

1-27

THEORY AND ADJUSTMENT TO INSURE PROPER FUNCTIONING OF CORD

To adjust for tension -
adjust spring

s

with

screw

r

until there is

sufficient friction on
cord to lift weight
upward to contact
throat plate

The excess end of the cord after the trimming must be pulled back with enough cord left in the throat
plate to insure the proper start of another buttonhole - weight

p

on cord pull back serves to do this

the drop of this cord. Pull back is adjusted by loosening screw

n

and adjusting stop

o

to suit.

(Spring

s

in Figure 2, acts

o

,

p

has a clamp and a tension on cord) . To adjust - the yoke

t

is

taken off the race by pressing inward the plunger

q

and adjusting with screw

r

. When proper

adjustment is made - cord can not be drawn backward.

SHEAR ADJUSTMENT

TO ADJUST THE HOLD DOWN FINGER

Note:

This finger has been supplied with an
adjustable screw   - to adjust loosen
nut   turn screw    to suit and lock
with nut   after obtaining desired
pressure of finger on work.

This machine is supplied with a hold down finger for holding the
work while cutting of thread takes place and regular clamp arms are
up. Adjust by loosening nut and adjust screw for proper
clearance and easy insertion of work.

Do not sharpen blades from the top or flats.
Stone the edges only at (X) and (XX).

q

p

o

t

n

r

s

t

p

u

For tension upon
the blades,
loosen nut

v

and screw down
on screw

u

.

v

w

CORD TRIM - MACHINE ADJUSTMENT

«
...
37
38
39
40
41
...
»

Содержание Reece 101





























































Отзывы:

Нет отзывов